Currently working in Pakistan Petroleum Limited under third party contractor as a Plant Operator at Gambat South Blocknlocated in District Sanghar , Sindh from March 2012 to till date .
Gas Processing Facility: Designed to treat 70 MMSCFD Raw Natural Gas and consisting of
 SCADA Gas Control System: Pressure & Flow Control on far away located wells by an online Gas Control System
 Amine Sweetening Unit : Inlet Filter Separator, Bubble Cap Tray Type Amine Absorber, Amine Stripper, Amine Flash Tank, Cattle Type Amine Reboiler, Lean Amine Cooler, Reflux Condenser, Multistage Centrifugal Type Amine Booster and Reflux Pumps, Plate And Frame Type Amine Heat Exchanger, Sock and Charcoal Filters.
 Glycol Dehydration Unit : Bubble Cap Tray Type Glycol Absorber, Glycol Flash Tank, Glycol Rebolier , Kimary Glycol Charge Plunger Pumps, Double Pipe Glycol/Glycol Exchanger, Sock and Charcoal Filters, Dry Gas Cooler.
 Instrument Air Skid: Screw Type Instrument Air Compressor, Wet Air Receiver, Desiccant Air Dryer and Dry Air Receiver.
 Three Phase Production Separator, Cooling Tower, Metering Skid, Flare System, Sour Water Treatment Unit Fuel Gas Skid, Incinerator, Reverse Osmosis Unit.
Responsibilities:
Worked as Plant Operator for treating 70 MMSCFD raw natural gas.
 Preparation/analysis of safe operating procedure for different jobs such as safe shutdown, safe start-up, emergency condition and other routine jobs.
 Optimizing plant operation, performance monitoring, processing of gas according to specs i.e keeping the Sulfur & Moisture contents within specified limits.
 Handling of day to day operational troubleshooting, modifications.
 Sale gas calculations from flow charts with complete material and energy balance.
 Completion of checklists before start up, tracing of faults/abnormalities.
 Isolation / depressurization on any running section / equipment of plant to facilitate maintenance department to work and then to normalize the system after completion of job.
 Analyzing daily log sheets, production data, and Lab reports to provide data to engineering team.
 To control the process parameters through wide variety of controlling system.
 Responsible for issuance and implementation of “Permit To Work” system.
 Ensure implementation of wearing of Personal Protective Equipments (PPE’s) to all field staff.
 Participate in Risk Assessment preparation and ensure recommended safeguards are implemented and performing teams are in full awareness and adhering to the risk assessment terms & conditions

Attend one year training from June 2010 to June 2011 & then as Production Engineer till December 2011. During this tenure at Olympia Chemicals Limited (450 Tons/Day Sodium Carbonate & Sodium Bicarbonate) production unit, I got an ample experience of following equipments/operations.
• Removal of TSS from water by Sedimentation, Coagulation, Flocculation & through Gravity Sand Filters.
• Soft water plant (hot soda lime process)
• Operation of double acting two stage reciprocating compressors.
• Operation, handling and troubleshooting of cross and counter flow induced draft cooling towers.
• Operation of centrifugal, positive displacement and multistage centrifugal pumps.
• Recovery of ammonia from flash distillation, ammonia gas absorption in refined brine and CO2 absorption in carbonating towers.
My job responsibilities were
• Preparation/analysis of safe operating procedure for different jobs such as safe shutdown, safe start-up, emergency condition and other routine maintenance jobs.
• Technical support for all the equipments, operations involved in the production of Soda Ash.
• Optimizing plant operation, performance monitoring, management of shift, processing of reactants according to specs within specified limits.
• Day to day operational troubleshooting, modifications, commissioning.
• Soda Ash Production calculations with complete material and energy balance.
• Completion of checklists before start up, tracing of faults/abnormalities.
• Isolation / depressurization on any running section / equipment of plant to facilitate maintenance department to work and then to normalize the system after completion of job.
• Analyzing daily log sheets, production data, and Lab reports to provide data to engineering team.
• To control the process parameters through wide variety of controlling system.
• Schedule testing of various equipment on weekly/ monthly basis.